GÄN GA+
TUNING BOX
or
REMAPPING
Today there are 2 ways of chip tuning: additional tuning box (tuning modules) and software changes in the ECU (remapping).
These two ways cause disputes among consumers and it is very important to make the responsible choice of the most appropriate and correct solution for both the car itself and its owner.
Below guide will show why the use of tuning modules is more preferable than remapping.
#1. ENGINE
You shouldn’t worry about your engine
With tuning module, no engine components are altered, the engine won’t exhaust its performance potential prematurely and this won’t lead to breakdowns of any mechanical part. GAN GA+ software is licensed and safe for the engine, and it doesn't void your warranty.
Loss of the manufacturer’s engine warranty in case of ECU remapping
In case of ECU remapping you will lose your manufacturer’s warranty, even if the breakdown is a result of a manufacturing defect.
#2. FINE-TUNING
Customized
GAN modules
GÄN modules are programmed specifically for your engine. For GAN GA+, you have 5x Re-Programming if you Switch Cars.
Remapping
of engines
Remaps, in most cases, are developed for a whole vehicle line regardless of specific engine type. Thus, tuning of separate components is not feasible.
#3. INSTALLATION
Simple
GÄN installation
You don’t need a lot of time or mechanic service to install a tuning box on your car. Installation usually takes within 15 minutes and does not require professional knowledge.
The complex and expensive remapping
Remapping takes much longer and requires special expensive equipment and an experienced specialist to ensure no damage is done to the ECU.
#4. SECURITY SYSTEM
Double security system
of GÄN modules
Since the tuning modules do not alter the ECU, all security systems work properly. In addition, the equipment that was tested multiple times will ensure the engine life does not exhaust prematurely.
Possible overload
due to remapping
Manufacturer’s protection mechanisms can get overridden once reprogrammed. This can result in overpressure and overheating. As such the engine will malfunction quickly.
#5. RESET TO FACTORY SETTINGS
Instant reset
to factory settings.
GAN modules can become “invisible” for your car and return your car to factory settings with just a click in the mobile App. But if you need to visit your auto dealer, it can take a little time, just a few minutes, to remove the equipment so no trace could be detected while your car is being serviced.
Complicated and long factory reset in case of remapping
It’s very difficult to return the ECU program to factory settings. It takes a lot of time and effort. Your auto dealer can still track that the program has ever been overridden.
#6. TRANSFERABLE
5X-Reprogramming if you switch car
If you change your car, you can transfer the GAN to your new car. For example, if now you drive a car with naturally aspirated engine or Hybrid car, then you can transfer the GA+ to your new naturally aspirated engine or Hybrid car, up to 5X-Reprogramming. Save Money!
Non-Transferable if you switch car
It’s not possible to transfer remapping if you switch car. So you will have to spend extra money for tuning of car performance.
GÄN. PLUG & PLAY IN.
GAN GA+ is an additional control unit that is plugged into your car’s OBD II connector. The control unit receives the information directly from the engine system. The optimization software of the unit modifies the signals and then transmits them to your vehicle's ECU in order to maximize power and torque.
GAN can reduce fuel consumption by adapted driving behavior. The increased torque primarily at low and mid-range RPM and faster upshifts result in a higher speed at a lower RPM and therefore fuel economy.
GAN can reduce fuel consumption by adapted driving behavior. The increased torque primarily at low and mid-range RPM and faster upshifts result in a higher speed at a lower RPM and therefore fuel economy.
FUEL AND MONEY ECONOMY
With our GÄN you don't have to choose between better performance and fuel economy. You get both with the GÄN. With appropriate driving habits, you can improve fuel economy by up to 15% by using the GÄN.
As higher efficiency brings more torque, gear switch takes place earlier and less often. This lowers fuel consumption. GÄN works with factory ECU firmware and you will see the true data of lower fuel consumption which cannot be guaranteed by remapping.
As higher efficiency brings more torque, gear switch takes place earlier and less often. This lowers fuel consumption. GÄN works with factory ECU firmware and you will see the true data of lower fuel consumption which cannot be guaranteed by remapping.
-15%
MADE IN GERMANY AND TESTED IN VARIOUS CONDITIONS.
It's no secret that German-made products always have a quality mark and reliability in every component! Each individual part meets automotive industry standards and the stylish housing is made from aluminium. GAN products are used all over the world Today. More than 100,000 customers enjoy the new features of their car.
FINE TUNING VIA YOUR SMARTPHONE.
GAN developed a mobile app that connects to the tuning module via Bluetooth. You can choose among several driving modes that were designed and configured individually for each engine: Dynamic, Eco, and Stock.
The software is customized specifically for each engine.